One reduction worm gearing offers high ratio reduction with couple of shifting parts in a close-coupled small drive. The proper angle arrangement of driving-to-driven machine requires a the least space. Input and result shafts can be prolonged in either or both directions in horizontal or vertical arrangements adaptable to any mounting requirement. Efficient engine speeds are decreased to sluggish speed requirements of several industrial machines in one reduction.
Product Features
Ratios 5:1 to 70:1
Hollow & Solid Output Shafts
Vertical & Horizontal Mounting
Fan Cooled (Standard)
Motor Mounts (C-Encounter Adapters or Scoops)
Cast Iron or Metal Housings
Products
The exclusive use of the involute Helicoid Thread form (with leaving side contact) on the worm and gear offers high efficiencies, and long service existence. The hardened ground and polished alloy steel worm develops a easy, work hardened surface area on the bronze gear. For this reason worm gears put on in and improve with prolonged service while additional gears are wearing out. Ever-Power offers a broad selection of model configurations, sizes, ratios, and accessories from our standard products.
Fabricated Designs
If your application involves severe shock loads or feasible housing damage from external sources (as in steel mills or mobile products applications) Ever-Power can provide fabricated steel housings with up to 48″ center distances. Fabricated housings provide optimum rigidity and strength which allows the tranny of higher horsepower levels than are possible with regular cast iron units. Extra heavy aspect plates connect the worm and equipment shaft bearing supports, assuring appropriate meshing of the gear under all load conditions. In smaller sized sizes, fabricated steel reducers are interchangeable 
with Ever-Power regular cast iron reducers.
Custom Designs
Ever-Power can provide custom swiftness and reversed engineered reducers for the application, be it a new project or a primary drop-in replacement for a competitor’s quickness reducer. Fabricated metal reducers allow Ever-Power to match a competitor’s footprint, centerline, and shaft elevation allowing a direct drop-in substitute saving the customer time and money.
Long – Quiet Life
All worm gears in Ever-Power reducers are manufactured from phosphorous bronze. Our design also includes a hardened, surface and polished alloy metal worm. This mixture develops a smooth, work-hardened mating surface of the bronze gear which boosts with prolonged service.
Worm gearing is a course of equipment reducers that utilizes correct angle, nonintersecting shafts. This form of reducer provides clean and quiet operation and permits the possibility of large rate reductions. These gears are available from share in a wide selection of ratios, from only 4:1 up to 3600:1. The compact design and building allows worm gear reducers to be placed in a comparatively small space. Thus, high reductions in a limited package size may be accomplished with this configuration. Our worm equipment features the continuous sliding tooth actions between worm and one’s teeth. This escalates the tolerance for weighty loads and shock loads. Worm gear drives offer users high reducing convenience of relatively low cost when compared to some other types of gearing.
The usage of worm gearing extends across many industries including food, beverage and grain and has many applications. Some applications that utilize worm gearing are: conveyors, mixers and bucket elevators.
Ever-Power worm equipment reducer gearbox series base on years of encounters uses designed teeth surface with unsurpassed torque transfer efficiency with great functionality, efficency and price.Worm gear system transmits power through sliding get in touch with, resulting in extremely low worm gear speed reducer vibration , sound, little backlash and self-locking property
-Housing:One time we casting creats great rigidity for severe impacts. Outer cooling fins and internal lubrication essential oil diversion channel style to increase heat dissipation.
-Worm Shaft: Manufactured with Carbon alloyed Steel S45C or SCM415, precison machined and carburized to HRC45 or HRC60, then for precision tooth grinding to make sure maximum contacting.
-Worm Wheel: Manufactured with Carbon alloy ALBC2, teeth are machined by precision CNC hobbing machine to sustain high impact.
A worm equipment reducer is one type of reduction gear box which contains a worm pinion input, an output worm gear, and includes a right angle output orientation. This kind of reduction gear container is normally used to have a rated motor quickness and create a low speed result with higher torque worth based on the reduction ratio. They often times can resolve space-saving problems because the worm equipment reducer is among the sleekest decrease gearboxes available due to the little diameter of its output gear.
worm gear reducerWorm gear reducers are also a favorite type of swiftness reducer because they offer the greatest speed decrease in the tiniest package. With a high ratio of speed reduction and high torque result multiplier, it’s unsurprising that lots of power transmission systems utilize a worm equipment reducer. Some of the most common applications for worm gears can be found in tuning instruments, medical assessment equipment, elevators, security gates, and conveyor belts.
SW-1 and SW-5
Torque Transmission provides two sizes of worm gear reducer, the SW-1 and the SW-5 and both can be found in a variety of ratios. The SW-1 ratios include 3.5:1 to 60:1 and the SW-5 ratios include 5:1 to 100:1. Both of these options are produced with tough compression-molded glass-fill up polyester housings for a durable, long lasting, light weight speed reducer that’s also compact, non-corrosive, and nonmetallic.
Features
Our worm gear reducers offer a choice of a solid or hollow result shaft and show an adjustable mounting position. Both the SW-1 and the SW-5, however, can endure shock loading better than other decrease gearbox designs, making them perfect for demanding applications.
Rugged compression-molded glass-fill polyester housing
Light weight and compact
Non corrosive
Non metallic
Range of ratios
SW-1, 3.5:1 to 60:1
SW-5, 5:1 to 100:1
Grease Lubrication
Solid or Hollow output shaft
Adjustable mounting position
Worm Equipment Reducers also referred to as worm gearbox or worm acceleration reducers. Worm gear reducers are used for speed reduction and increasing the torque for electric electric motor drives. You can decide to install your NEMA engine to the reducer by using the NEMA C encounter flange or use a coupling. If you need a coupling for the output or input shaft see our coupling section for choosing the coupling. We offer four assemblies left hands and right hand and double output shaft and shaft input and shaft output. Interchangeable with most worm gear manufactures. See data sheet in product overview for diamensions. Unless you see your type, please Contact Us.
8 Ratios Available from 5:1 to 60:1
7 Gear Box Sizes from 1.33 to 3.25″
Universally Interchangeable Design for OEM Replacement
Double Bearings Used on Both Shaft Ends
Anti-Rust Primer Applied Outside and inside Gearbox
Shaft Sleeve Protects All Shafts
S45C Carbon Steel Shafts
Flange Mount Versions for 56C and 145TC Motors
Ever-Power DDVM series triple-reduction worm gear quickness reducers are available in ratios from 5000:1 to 175,000:1 and middle distances from 7” to 20” (larger sizes available on request). Result torque ranges from 33,000 in pounds. for the 7” CD DDVM-70 to 582,900 in lbs for the DDVM-200. Mechanical HP input requirements are from 0.09 HP for the 175,000:1 7 in CD reducer to 6.25 HP for the 5000:1 20” CD unit. These reducers are available in four configurations: horizontal, vertical, shafted, and shaft mounted.
These reducers are perfect for water/waste-water products drive applications such as for example thickeners and clarifiers, which require a vertical straight down shaft. Other offered configurations also make Ever-Power triple decrease reducers perfect for make use of on mixers, elevators, solar panels, astronomical telescopes, indexing tables, hoists, conveyors, or other process or components handling systems where huge torques/gradual speeds are needed.
These reducers are also available with a helical primary reduction stage and so are termed the HDVM series
Product Features
Ratios 5000:1 to 175,000:1
HP from 0.09 to 6.25.
Output Torque to 583,000 in lbs.
Output RPM only 0.01 with a 1750 RPM input.
Ideal for ultra-slow velocity, high torque applications
8 Ratios Available from 5:1 to 60:1
7 Gear Box Sizes from 1.33 to 3.25″
Universally Interchangeable Style for OEM Replacement
Double Bearings Used on Both Shaft Ends
Anti-Rust Primer Applied Outside and inside Gearbox
Shaft Sleeve Protects All Shafts
S45C Carbon Metal Shafts
Flange Mount Models for 56C and 145TC Motors
Description
The HDR Series worm gear reducers are found in low to moderate horsepower applications to reduce speeds and increase torque. Worm gear reducers can be found in direct or indirect drive, direct drive models are 56C or 145TC flange mount with either right, left or dual result shafts or a hollow bore output. The indirect drive models are shaft input-shaft output boxes for use with sprocket or pulley drive systems. They offer an effective low cost solution to speed decrease and increased torque, with higher tolerances for shock loading than helical gear reducers.
In order to decide on a gearbox speed reducer, you will need to determine the required torque and program factor for the application. Click on “Specs” above for a desk that will aid in determining the service element. For service factors above 1.0, multiply the required torque by the assistance factor.
Our standard 700 Series – the heart of Ever-Power quickness reducer products – has been serving industry reliably for over 40 years. Its proven modular style has set the industry standard for overall performance and may be the most imitated product in the current worm gear rate reducer marketplace. But why accept a knock-off when you can have the initial – from Ever-Power.
Specifications
11 basic single reduction sizes
8 basic dual reduction sizes
1/6 – 25 HP
5:1 – 100:1 ratios single reduction
100:1 – 3600:1 ratios double reduction
Non-flanged, NEMA C-face quill, and coupled input styles
Projecting and hollow result shafts
Projecting diameters from 1/2″ to 2-1/4″
Hollow output bore diameters from 5/8″ to 3-7/16″ (with over 20 bore sizes in stock)
Product Features
The 700 Series’ huge oil reservoir provides efficient heat dissipation and lubrication for longer operating life.
Its multi-position mounting versatility allows for installation in virtually any position.
Housings are straddle-milled, top and bottom level, for precise alignment of horizontal and vertical bases.
Internal baffles assure positive, leak-free venting.
The 700 Series’ rugged casing, fabricated of fine-grained, gear-quality cast iron, provides optimum strength for optimum durability, as well as greater precision during worm and gear alignment.
Ever-Power 700 Series high-strength bronze worm gear is straddle mounted between heavy-duty tapered roller bearings to increase thrust and overhung load capacities, sizes 713-760.
Our 700 Series’ high-strength steel result shaft assures convenience of high torque and overhung loads.
Pipe plugs allow easy fill up, level, and drain in virtually any mounting position.
The 700 Series’ super-finished oil-seal diameters on both input and output shafts extend seal lifestyle.
Both 2D and 3D CAD drawings are available in our eCatalog.
TheIncreased Quality! Industrial Rated! Inexpensive!One-piece gearcase, without exterior ribs, is made of close-grained cast iron and provides for rigid gear and bearing support. In addition, it offers excellent high temperature dissipation.Dual lip, spring-loaded seals protect from oil leakage and prevent dirt from entering.Stepped shafts with oversized ball andtapered roller bearings.Carbon steel shafts for greater strength.High tensile strength cast bronze worm wheel and hardened and ground alloy steel worm made intregal with the shaft for lengthy and trouble-free life.Essential oil sight gauge for ease of maintenance (unavailable upon sizes 25 and 34).Factory oil filled.Every device test run just before shipment.Universal installation with bolt-on ft.Highly modifiable design.All this at substantially cheaper prices than you have been accustomed to paying for reducers of lesser quality. Less
